Home > Products > Digital Indicator > CSD - 819C

Digital Indicator

Digital Peak Holder CSD-709 New release

Digital peak holder CSD-709
Feature
  • High speed sampling speed at 4 000 times/s
  • Corresponding to the various application
  • Holding function corresponding to the application.
  • Various interface.
  • Waveform display and condition setting is available with PC by the additional memory and the specialized software.
  • CE Mark applicable.
  • Protection class: IP64 or equivalent
Specifications
Bridge power supply DC10 V}0.5 V within 60 mA (Changeable to DC5 V or DC2.5 Vj
Applicable transducer Strain gage based transducer 170 Ω ~ 1 000 Ω
(at 10 V of bridge power supply)
Input sensitivity 0.4 μV/d (d = Minimum scale)
Input range |3.1 mV/V ` 3.1 mV/V
Zero adjustment range ±2.5 mV/V
Monitor output 2 V ± 0.1 V per 1 mV/V of sensor input (at 10 V of bridge power supply)
Load resistance: 2 kΩ or more
Non-linearity 0.02 %±1 digit
Temperature coefficient Zero point ±0.5 μV/
(in the calibraton with 0.4 μV/d or more of input sensitivity.)
Sensitivity ±0.002 5 %F.S./
(In the calibration with ±0.4 μV/d or more of input conversion.)
Analog filter 100 Hz (Changeable to 10 Hz, 40 Hz, 400 Hz, 1 kHz, 4 kHz, 10 kHz or 30 kHz.)
* Effective only when analog peak hold is used.
* Fixed to 30 kHz when digital peak hold is used.
Digital low pass filter 40 times/s: OFF, 0.1 Hz` 4 Hz
400 times/s: OFF, 1 Hz` 40 Hz
4000 times/s: OFF, 10 Hz` 400 Hz
A/D sampling speed 4 000 times/s (Changeable to 40 times/s or 400 times/s)
A/D internal resolution 24 bit
CHECK value Approx. 0.3 mV/V
Analog peak hold Response speed: According to the property of analog filter.
Analog filter set value 10
Hz
40
Hz
100
Hz
400
Hz
10
kHz
4
kHz
Accuracy Analog filter set value (-3 dB±1 dB) ±0.1 %
Analog filter set value 10 kHz
Accuracy Analog filter set value (-3 dB±1 dB) ±0.5 %
Analog filter set value 30 kHz
Accuracy Analog filter set value (-3 dB±1 dB) ±1 %
Main display
(Load display)
Display range: |99 999 ` 99 999
Display incriment: 1 (Changeable to 2, 5 or 10.)
Display unit: Green 7 segment LED, Character height: 17 mm
Over display: [-OL] appears in case of minus overflow, [OL] appears in case of plus overflow.
A/D value over display: [-OVF] appears in case of minus overflow, [OVF] appears in case of plus overflow.
Condition display SEL.1ASEL.2ACHECKAHOLDAPEAKAMEAS.AENDALOCK
Judgement display OUT1, OUT2, OUT3, OUT4
Display rate 20 times/s (Changeable to 4 times/s, 50 timess or 100 times/s)
Decimal display Changeable to no display, 101, 102, 103 or 104.
External control input signal Any 6 signals listed below is selectable.
OFF, Zero set, Zero set clear, HOLD (pulse), Print command (Serial interface), Forced termination of multi-hold, HOLD (Level), Peak/Track, Reset, SEL.1, SEL.2, CHECK, Batched key lock
External control output signal Any 6 signals listed below is selectable.
OFF, HOLD, PEAK, MEAS, END, MULTI (turned on in using multi-hold mode.), EXCUTE (turned on during measurement in multi-hold mode), NG (turned on under any condition except for OK condition.), Upper limit / Lower limit, S0, S1, S2, ERROR, Over error, Zero set response, RUN (Level / Toggle)
Functions Analog filter, Digital filter, Digital low pass filter, Simplified calibration, CHECK value, Hold target change, Analog output target change, Brand code change, Peak mode selection, Digital peak hold, Analog peak hold, Monitor output, Monitor mode, Waveform comparison (when the optional parts is installed.), Measurement result log (when the optional parts is installed.)
USB interface Compatible with USB 2.0 (can also be used with USB 1.1 compatible equipment)
Output connector: B type mini-USB connector
Operating temp./humidity range Temperature -10 ~ 50 ,
Humidity 85 %RH or less (Non condensing)
Power supply voltage 100 VAC ~ 240 VAC 50/60 Hz
(Permissible variable range 85 VAC ~ 264 VAC)
Power consumption Approx.10 VA (without options, at 100 VAC)
Approx.18 VA at maximum (with options, at 100 VAC ~ 240 VAC)
Outline dimensions(WxHxD) 96 mm x 48 mm x 110 mm (excludes protruding parts)
Weight Approx. 500 g (without options)
Protection code IP64 or equivalent at the front panel section when the gasket is installed.
Options
Voltage output, Current output, BCD output (Sink type), BCD output (Source type), External control (Voltage input type), RS-232C interface, RS-422/485 interface, CC-Link interface, Power supply voltage, Serial interface, Additional memory (with software for measurement CSD-709D-01), EzCTSiEz Communication Tool Software for PCj
Download
CAD files (DXF) Specification sheet (PDF) Instruction manual (PDF)
CSD-709 (437KB) No.EN382709 (183KB) No.EN294-1742-E (4,002KB)
Chinese
No.CN294-1742 (3,909KB)
Start guide
No.EN294-1768 (2,976KB)
Supplementary for CC-Link interface
No.EN294-1701 (460KB)
Software for measurement
CSD-709D-01
No.EN294-1761 (1,786KB)
USB driver (Applicable OS: Windows vista, Windows7, Windows10)
USB_driver.zip (1,323KB)
File for CSP+(CC-Link Family System Profile Plus)
0x0210_CSD-709_1.00_en.zip (280KB)
Adobe Acrobat Reader is required to refer the Specification data sheet.
Acrobat Reader is a registered trademark of Adobe Systems Ltd.
The download of Adobe Acrobat Reader is here.